synth_tools

Back

20x20 grid, 17x17mm package, 1mm pitch; https://www.xilinx.com/support/documentation/user_guides/ug475_7Series_Pkg_Pinout.pdf#page=264, NSMD pad definition Appendix A BGA 676 1 FG676 FGG676 Spartan-7 BGA, 14x14 grid, 8x8mm package, pitch 0.4mm; see section 7.7 of http://www.st.com/resource/en/datasheet/DM00330506.pdf WLCSP-100, 10x10 raster, 4.201x4.663mm package, pitch 0.4mm; see section 7.4 of http://www.st.com/resource/en/datasheet/stm32l052t8.pdf WLCSP-36, 6x6 raster, 2.605x2.703mm package, pitch 0.65mm UFBGA-32, 6x6, 4x4mm package, pitch 0.35mm; see section 7.5 of http://www.st.com/resource/en/datasheet/stm32l152zc.pdf WLCSP-64, 8x8 raster, 4.466x4.395mm package, pitch 0.5mm; see section 7.5 of http://www.st.com/resource/en/datasheet/DM00257211.pdf WLCSP-49, 7x7 raster, 3x3mm package, pitch 0.4mm; see section 7.1 of http://www.st.com/resource/en/datasheet/stm32f051t8.pdf WLCSP-36, 6x6 raster, 2.553x2.579mm package, pitch 0.8mm Altera BGA-68 M68 MBGA Altera VBGA V81 BGA-81 Altera BGA-100 M100 MBGA 121-ball, 0.8mm BGA (based on http://www.latticesemi.com/view_document?document_id=213 Lattice caBGA-756, ECP5 FPGAs, based on ** https://www.instructables.com/Another-MIDI-to-CV-Box-/ yet another version Alternative: CV from something else VCF MK's Diode Ladder VCF ~$8 in parts, needing only one cross-board wire that shouldn't be so hard. - In general, try to avoid putting any UX connections on the cylindrical edge of the rail + a safety margin width_mm = 70.8; // 14HP×5.08mm = 71.12; ES for 14HP is 70.8 c_tune = [width_mm/2, top_row, 0]; f_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [second_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; triangle_out = [output_column, row_1, 0]; saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement sync_in = [first_col, third_row, 0]; saw_out = [third_col, fourth_row, 0]; pwm_cv_lvl = [second_col, second_row, 0]; //Third row interface placement fm_in = [h_margin+working_width/8, row_3, 0]; right_rib_x = width_mm - h_margin; input_column = h_margin; col_middle = col_left + (15.6 + 1.5 + 7 + 8); // pot + led + switch? Col_right = width_mm - col_right; // column from edge plus hole radius h_wall(h=4, l=slider_spacing * 10 + center_adjust; right_col = width_mm - h_margin.

New Pull Request

Labels Milestones