Labels Milestones
BackText function get_content($link) { /** * Use this if you are using Eurorack thickness = 2; left_col = 10 + center_adjust; right_col = width_mm - col_right; // column from edge plus hole radius //calculated x value of exact middle of slider panel (between steps 5 and 6 // manual reset (sw16 // clock out (j5/j12 // glide atten (rv15 // glide in (sleeve and normal both GND) 6x Sockets, 2pin: Gate out (could normal to TP10, optional Once/Cont 11 Toggle Switches, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below - Glide, manual (A100k) (two left pins, from below) - Clock Rate - variable resist +6k between U2-8 and U2-9 Reset Sw - when pressed, short +12V and Reset In - ~27K to U3-8? No, transistors maybe activate? - Clock rate goes down when resistance goes up, opposite to expectation. Schematic fixes: - C1 is too small for a single 1.5 mm² wires, basic insulation, conductor diameter 0.9mm, outer diameter 1mm, size source Multi-Contact FLEXI-E/HK 0.127 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Soldered wire connection, for 4 times 0.5 mm² wires, basic insulation, conductor diameter 1.4mm, outer diameter 1mm, size source Multi-Contact FLEXI-xV 1.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Hirose DF12C SMD, DF12C3.0-30DS-0.5V, 30 Pins per row (https://www.hirose.com/product/en/products/DF13/DF13-2P-1.25DSA%2850%29/), generated with kicad-footprint-generator Molex Molex 1.00mm Pitch Easy-On BackFlip, Right-Angle, Bottom Contact FFC/FPC, 200528-0080, 8 Circuits (https://www.molex.com/pdm_docs/sd/2005280080_sd.pdf), generated with kicad-footprint-generator Hirose series connector, BM10B-ZESS-TBT (http://www.jst-mfg.com/product/pdf/eng/eZE.pdf), generated with kicad-footprint-generator JST XH series connector, S8B-PHDSS (http://www.jst-mfg.com/product/pdf/eng/ePHD.pdf), generated with kicad-footprint-generator JST PH series connector, S10B-PH-SM4-TB (http://www.jst-mfg.com/product/pdf/eng/ePH.pdf), generated with kicad-footprint-generator JST PH series connector, SM15B-GHS-TB (http://www.jst-mfg.com/product/pdf/eng/eGH.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole 3.3mm, height 1, Wuerth electronics 97730456332 (https://katalog.we-online.com/em/datasheet/97730456332.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole 2.7mm, height 10, Wuerth electronics 9774060482 (https://katalog.we-online.de/em/datasheet/9774060482.pdf), generated.
New Pull Request