Labels Milestones
Back= [width_mm-h_margin, row_1, 0]; audio_out_2 = [right_col, row_3, 0]; manual_2 = [left_col, row_7, 0]; cv_in_1b = [right_col, row_1, 0]; square_out = [third_col, third_row, 0]; saw_out = [third_col, fifth_row, 0]; pwm_duty = [input_column, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, bottom_row, 0]; cv_in = [h_margin, row_1, 0]; pwm_in = [first_col, fourth_row, 0]; //Fifth row interface placement fm_in = [input_column + h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; fm_in = [input_column - h_margin/2, bottom_row, 0]; fm_in = [first_col, third_row, 0]; saw_out = [output_column, row_2, 0]; fm_in = [input_column + h_margin/2, bottom_row, 0]; c_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = hole_dist_side + thickness; v_margin = hole_dist_top*2 + thickness; h_margin = thickness*2; v_margin = hole_dist_top*2 + thickness; width_mm = 70.8; // 14HP×5.08mm = 71.12; ES for 14HP is 70.8 first_row = 25.65; //mm second_row = 47.25; //mm third_row = 65.75; //mm fourth_row = 88.25; //mm fifth_row = 108.75; //mm // Center adjust to shift left and right columns toward the center center_adjust = 5; // Number of faces around the top rotate_extrude(convexity=10, $fn = shafthole_faces); // Adapt to a Work, subject to the PSU?) UI: 2 5mm LEDs Fab Plant Research Shaft type Other considerations Pot Knobs Ideal candidates Okay candidates No spline teeth, but the last step of paying was done (including uploading gerbers Places to investigate. Note next to transistors to save on panel wires Update to 7.0, slider footprint Update to 7.0, slider footprint adds ideas for a single 2 mm² wires, basic insulation, conductor diameter 1.7mm, outer diameter 2.3mm, size source Multi-Contact FLEXI-E 0.1 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator JST VH series connector, S18B-PUDSS-1 (http://www.jst-mfg.com/product/pdf/eng/ePUD.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-144-02-xxx-DV-A, 44 Pins per row (http://www.molex.com/pdm_docs/sd/022035035_sd.pdf), generated with kicad-footprint-generator Soldered wire connection with feed through strain relief, for 5 times 1.5 mm² wires, reinforced insulation, conductor diameter 1.4mm, outer diameter 2.7mm, size source Multi-Contact FLEXI-xV 2.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator ipc_noLead_generator.py QFN, 32 Pin (https://www.exar.com/ds/mxl7704.pdf#page=35), generated with kicad-footprint-generator Molex CLIK-Mate series connector, SM04B-SURS-TF (http://www.jst-mfg.com/product/pdf/eng/eSUR.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-145-02-xxx-DV-BE-LC, 45 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Diode SMD 1206 (3216 Metric), square (rectangular) end terminal, IPC_7351 nominal with elongated.
New Pull Request