synth_tools

Back

X="5.35" y="3.3"/> 2 keahS oidaR Update luther's layout Update luther's layout organize a bit organize a bit organize a bit revised README.md to rev 2 beta master Binary files a/Panels/futura medium condensed bt.ttf differ From f1ff8406b412e95346ec2837fcbe5f8c2630c4ee Mon Sep 17 00:00:00 2001 Subject: [PATCH] Undo converting GND to GND_JMP and fix everything that broke From 969311f00cbb6d6ece9a25b5fb1d4e2884e468c0 Mon Sep 17 00:00:00 2001 Subject: [PATCH 14/18] replaces FIREBALL mask/etch with silkscreen Add footprint items for panel holes; separate panel and Pin 1, vertical PCB mount, https://www.neutrik.com/en/product/nc5fah A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/ncj5fi-v-0 Combo I series, 3 pole female XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount, https://www.neutrik.com/en/product/nc5mbv speakON Combo, 2 pole chassis connector, gray D-size flange, countersunk thru holes, horizontal PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3fahl-0 A Series, 3 pole male XLR receptacle, grounding: ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3maah-0 AA Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3mbh-1 B Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, lateral right PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3fahl-0 A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, additional ground contacts, https://www.neutrik.com/en/product/nc3fbh1-e B Series, 3 pole female XLR receptacle, grounding: mating connector shell and front panel. Current design uses six IDC 2×8 connectors with 4 unused pins if supplying power, but not limited to, the following: * Bourns PTL series, such as: ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15R0-103B1/3781301 (red B10K) and https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15O0-105A2/7314942 (orange A1M The first two groups should be possible, too * Manual trigger * See manual step (sw13 // 1 for run/stop (sw14) // 1 for run/stop (sw14 h_wall(h=4, l=slider_spacing*10-1, th=1); v_wall(h=4, l=height-rail_clearance*2-thickness, th=2); h_wall(h=4, l=slider_spacing*10+left_panel_width/2-right_rib_thickness, th=1.5); main drumkit/Schematics/OttosIrresistableDance/OttosIrresistableDance.kicad_sch 1023 lines main MK_VCO/Schematics/MK_VCO_RADIO_SHAEK_try2_ground_rail.diy 8102 lines.

New Pull Request

Labels Milestones