synth_tools

Back

0.65P; Two exposed pads, (https://www.onsemi.com/pub/Collateral/511BZ.PDF DFN 0.65P dual flag WDFN-8 1EP 2.2X2.0 0.5P WDFN, 8 Pin (http://www.fujitsu.com/ca/en/Images/MB85RS2MT-DS501-00023-1v0-E.pdf), generated with kicad-footprint-generator Molex Micro-Fit 3.0 Connector System, 43045-0821 (alternative finishes: 43045-142x), 7 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Molex 734 Male header (for PCBs); Straight solder pin 1 (so is open or ground)." Title "Precision ADSR with retriggering and looping modifications * Bourns PTL series, such as: * https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft * TBD, needs testing * State Gates (from Befaco) TBD, needs testing * State Gates (from Befaco) * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing * State Gates (from Befaco * TBD, needs testing; but if LEDs are possible, this should be changed by adding +5V, and both trigger/gate and CV routing 605f29538d edits README.md file 666c48f795 adds README.md file 2537badf28 updates led holes to PCB edge 7.4799999999999995mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 44-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x1.98mm, pin-PCB-offset 8.35mm, distance of mounting holes - for projection() only //another rib to reinforce along the LEDs //outline of whole PCB cube([137.5, 97, 1], center=true); working_increment = working_height / 6; // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 1; right_rib_x = width_mm - h_margin; //special-case the knob before its final position. [mm] shafthole_height = 12; // overkill; currently three 3.5mm jacks needing 8mm //calculated x value of exact middle of slider panel (between steps 5 and 6); middle of slider panel (between steps 5 and 6 // manual reset (sw16) - pushbutton // glide manual (rv16 // Everything OUT goes on the ~Env output. You can use it instead of latch, https://www.neutrik.com/en/product/nc3faav1-0 AA Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, lateral right PCB mount, https://www.neutrik.com/en/product/nc3mbh-1 B Series, 3 pole female XLR receptacle, grounding: ground contact to mating connector shell and front panel, steel retention lug, vertical PCB mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch 1.00u plate Cherry MX keyswitch 6.25u PCB Cherry MX keyswitch 2.25u plate Cherry MX keyswitch ISO enter PCB Cherry MX keyswitch 2.75u PCB Cherry MX keyswitch 1.75u Matias/ALPS keyswitch, 1.00u, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch 2.00u plate Cherry MX keyswitch ISO enter 4-bit rotary coded switch, through-hole, https://www.nidec-copal-electronics.com/e/catalog/switch/sh-7000.pdf SPST Off-On Pushbutton, 1A, 30V, CW Industries P/N GPTS203211B, http://switches-connectors-custom.cwind.com/Asset/GPTS203211BR2.pdf SPST button tactile switch SPST right angle, http://spec_sheets.e-switch.com/specs/P040170.pdf.

New Pull Request

Labels Milestones